![]() While it naturally takes years for a patina to form, we can speed up the process using a few simple techniques to create unique and eye-catching effects on our copper forging projects. Simply put, a patina is a thin layer that forms on the surface of metals, such as copper, due to exposure to natural elements over time.įor copper, this patina is usually a beautiful green or blue hue, often seen on historic buildings and statues (think of the Statue of Liberty!). Why Add Patina to Your Copper Creations?.Whichever method you end up with, exploring this particular intersection of art and science is an adventure. Make sure to read the info about each one to be sure you’re handling it properly. If none of the above patinas are what you want, you can also buy commercial products for everything from an easy verdigris for copper to brown for brass. Instead, put it in a closed container to dry out and then toss it in the garbage. Pro Tip: The fumes of liver of sulfur can be hazardous, so work in a well-ventilated area and don’t dump the liquid down the drain when you’re done. The jewelry will begin to darken until it becomes a blackish color.įinally, to give your piece interesting accents, polish the raised areas until gleaming highlights emerge and leave the recessed areas dark. Then add a small amount of liver of sulfur (nuggets or gel) to the cup. To speed up the process, soak your jewelry in a cup of warm water until the piece is warm too. One drop of water can ruin the whole batch. If you prefer to use the nuggets, be sure to store the container in a dry place. The liquid has a longer shelf life and fewer harmful chemicals. Liver of sulfur comes as small nuggets or a gel-like liquid. This method uses the same combo - heat and liver of sulfur. ![]() Liver of SulfurĮver go into a hot spring wearing a bright silver bracelet and come out with a dark band around your wrist instead? It was probably the sulfur in the water plus the heat that changed the color. Seal it with beeswax or an acrylic clear coat and you’re good to go. If you’d rather have a lighter hue, take steel wool to your piece of jewelry and remove some of the patina. Pro Tip: Let the color go a little longer than you might like, as this patina has a tendency to flake off. You’re most likely to see turquoise, blue and green but you really can’t predict what you’ll get! Then check back every few hours or so to see what colors come through. ![]() You can sprinkle a little more salt on the top if you’d like to speed things along. Then remove it, place it on a paper towel and let it air-dry. Let the jewelry soak for at least a half hour. Just keep the 1:1 ratio of vinegar to salt the same. If you have a bigger piece of jewelry, you’ll need more liquid to cover the piece completely. Three tablespoons of each are enough for a small pendant. Stir until the salt dissolves into the vinegar. Hey, kitchen magician! All you need for this technique are equal amounts of vinegar and salt. Acrylic clear coats, beeswax or renaissance waxes can help protect the surface and the color. When you’ve hit upon a shade you love, add a sealant to finish it off. Experiment and see what color works best for your piece. Pro Tip: Heating copper can result in drastic color changes to avoid this, pull the torch away slowly. Try not to get too attached to a particular tint until you get the hang of this technique, because a bright reddish tint (for instance) might quickly fade into a bluish tone. The key is to stop before you’ve gone too far. Heat PatinaĪs you heat copper with a torch, it starts to change color, turning different shades of bright red, purple and blue. Now it’s go time! 3 Ways to Patina Copper 1. Your piece will not only have a more satiny finish but when you do add a patina, it will have more surface to work on.Īfter you finish, handle the jewelry by its edges so you don’t transfer any oils back onto it. ![]() If you don’t, grab a scrubbing sponge (like Scotch-Brite) and gently scuff the surface. (That means no fingerprints!) If you have a pickle pot, this is a great time to get it out. To get the best results, prep your pieces first so they’re free from dirt and oil. Try ’em all and see which method you like best. You can patina your copper pieces three different ways, each resulting in a different look. If you’re looking to add dimension to your handmade copper jewelry, it’s a super fun technique to explore that’s a little wilder than the usual matte, shiny or brushed looks. Patina is the blueish-greenish layer on the surface of copper that comes from age or chemicals (we see you, Statue of Liberty!).
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |